|
|
|
|
|
|
| |
The Web's best Machine Design Guide for Mechanical Engineers and Designers
|
|
|
|
|
NOTE: You are not currently logged in,
login,
or register
to assure full site access.
|
Try these great interactive web apps and data tools (that we have written just for you) for your next design project.
| iCrank THREAD Apps and Data... |
•
ACME Thread Calculator
Type in the nominal size and threads
per inch for your ACME thread and get all the needed min and max diameters
for your machine drawing.
|
•
BUTTRESS Thread Calculator
Type in the nominal size and threads
per inch for your American National Standard BUTTRESS thread and get all the needed min and max diameters
for your machine drawing.
|
•
Screw Data Page
Check out this app that gives all of the relevant data for sockethead
capscrews, panhead machine screws, hexhead capscrews and flathead machine screws...
Simulates the TAD type "screw selector" slide-card.
•
METRIC Screw Data
Same as above, only in metric
|
•
Set Screw Data Page
Check out this app that gives all of the relevant data for
hex head and spline head set screws. Includes data for flat, cup, cone, oval and half-dog point set screws.
Simulates the TAD type "screw selector" slide-card.
|
|
•
Bolt Torque Chart
This app will generate a "Recommended Bolt Torque" chart based on your
custom inputs.
|
•
Standard Tap Size Chart
Gives the recommended drill size
for American standard and ISO metric threads
|
•
Drill Size Chart
Gives the decimal value for standard drill sizes
|
•
NPT Tap Size Chart
Recommended drill sizes for National Pipe Threads
|
•
Wrench Clearances
Suggested hex-head bolt/screw spacing and clearances needed for wrenches
including open-end, box and socket.
|
|
| iCrank SPRING Calculators... |
•
Compression Spring Design Calculator
Designing a compression spring? Here's a tool that allows you
to iteratively calculate a spring's characteristics by entering a few simple inputs.
|
•
Torsional Spring Design Calculator
Designing a torsion spring? Here's a tool that allows you
to iteratively calculate a spring's characteristics by entering a few simple inputs.
|
|
•
Wave Spring Design Calculator
Designing a wave spring? Here's a tool that allows you
to iteratively calculate a spring's characteristics by entering a few simple inputs.
|
|
|
|
•
O-ring Data Page
Check out this app that gives all of the relevant data for standard o-ring sizes:
OD/ID/cross-section/volume/metric for AS-568A uniform dash numbers
|
•
Shore Hardness Values Chart
Relative chart showing how Shore
A, Shore D and Shore 00 scales are related.
|
|
| MORE iCrank apps and data... |
•
Spur Gear Calculator
Calculate your spur gear data for American National Standard Coarse
Pitch Tooth Forms for pressure angles of 20 and 25 degrees (ref. ANSI B1.6)
|
•
Conversion Factors for Selected Units
A table containing your most often used units conversion factors.
You'll also find a printable wall-chart here!
|
•
Hardness Conversion (steel)
Enter a hardness value and getthe equivalent hardness in other common units
as well as estimated tensile strength. Or if you know tensile strength you can get the approximate hardness equivalent.
|
•
RPN Calculator - Web App!
Can't function without RPN? If your brain
is wired for RPN and you don't have one handy - fire up our online version and
crank those numbers out.
|
|
•
Standard Force and Shrink Fit Calculator
Input a nominal hole diameter and receive all of the dimensional allowances for the hole and shaft for class FN1 thru FN5 interference fits.
|
•
Sheet and Wire Gage Chart
Gives you the decimal value for standard sheet and wire gages.
Now gives values for SWG, AWG, BWG and Manufacturer's standard.
|
•
Surface Roughness
A chart showing the range of surface roughnesses
typical for a number fabrication processes.
|
|
Follow Us on LinkedIn:
| Member Status: |
Visitor |
| |
Non Premium Access |
|
Copyright 2023 iCrank.com All Rights Reserved.
|
|
You may not duplicate or redistribute in any form without prior written consent. |
| | |
|
